The Foundation of Plumbing Knowledge When Installing a Bathtub
The Foundation of Plumbing Knowledge When Installing a Bathtub
Blog Article
We've unearthed this post about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround directly below on the web and believe it made good sense to write about it with you over here.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Installing a tub isn't exactly brain surgery, but it does need strong plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably tough job. If the old bathtub is easily obtainable, the task can relocate immediately; if you need to open a wall to get rid of the old bathtub as well as place the new bath tub, the task is much harder. In either situation, the project is within a house handyman's skills, although you will certainly require a helper to move out the old tub as well as embeded in the new one. Make sure you have qualified on your own for the work and also are comfortable attempting it. Instead of employing a contractor to take over a halfway-completed project, it is better to consider using one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This short article will help you mount a brand-new bath tub in your washroom if you have actually currently purchased a brand-new bathtub and do not need to alter the setup of your previous supply of water pipes.
Your devices as well as material checklist need to consist of the following:
Preparing for the Installment
Firstly, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the tap includes a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets device to prevent strain on the bath tub.
Fit the flexible tap ports to the bottom of the two taps using 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you use every one of the provided washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be suited its last position.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you ought to do is separate the water. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite troublesome as a result of the limited accessibility that is often the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old sealing compound.
Prior to carrying on to fit the brand-new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Utilizing the two wood boards under its feet, put the bath tub in the required placement. The wooden boards are helpful in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four little points.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the tub up until the level reads degree.
To set up faucets, fit the bottom of the outermost versatile faucet connector to the proper supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Activate the supply of water and check all joints and also brand-new pipework for leakages and also tighten them if needed. Load the tub and likewise examine the overflow electrical outlet as well as the regular electrical outlet for leaks.
Finally, take care of the bath paneling as defined in the maker's user's manual. Tiling and also securing around the tub ought to wait till the bathtub has actually been made use of at the very least once as this will certainly settle it right into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in place in between the faucet and the sink. Safeguard the faucet in place with the manufacturer provided backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal tap adapters. The former kind ought to be attached to the tap ends first, tightening just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to crack an inflexible seal, creating the water to penetrate the wall in between the bath and also the tiling, causing complications with wetness as well as feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components as well as installations. They are sold in tubes and cartridges, and can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill the bathtub with water prior to securing, to allow for the motion experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the marketplace. It is a good idea to fit the tiles making use of waterproof or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
I am just very focused on Tools You Need to Install a New Bathtub and I hope you enjoyed the new blog post. Sharing is nice. You won't know, you could be doing someone a favor. Kudos for your time. Please pay a visit to our blog back soon.
Visit My Website Report this page